该职位来源于猎聘 职责描述: 2.0 Job Summary
职位概述 Ÿ Take full responsibility of Software development for automobile controllers, including technical development trend, requirements analysis from customer, Software architecture design, basic software development, application software development and software test, etc. Ÿ 负责汽车控制器的软件开发,包括技术发展趋势、客户需求分析、软件架构设计、基础软件开发、应用软件开发和软件测试等。 3.0 Key Responsibilities
主要职责 Ÿ Responsible for software design of automotive thermal management controller, OBW (On-board weight) controller, cleaning system controller and valve actuator. 负责汽车热管理控制器、OBW(车载重量)控制器、清洗系统控制器和阀门执行器的软件设计。 Ÿ Responsible for software requirement analyzing and software architecture design. 负责软件需求分析和软件架构设计。 Ÿ Responsible for basic software requirement analysis and basic software design. 负责底层软件需求分析和底层软件设计。 Ÿ Responsible for the software development of RTE. 负责应用层与底层接口开发。 Ÿ Responsible for the development of upper communication GUI host by C# or other language. 负责用C#或其他语言开发上层通信GUI主机。 Ÿ Responsible for software technical problem solving. 负责软件技术问题的解决。 Ÿ Participate in the construction of software development related processes, tool chains and databases, and coordinate internally and externally. 参与软件开发相关流程、工具链和数据库的建设,并进行内部和外部协调。 Ÿ Responsible for complete software-level testing(HIL,MIL etc.). 负责完成软件级测试(HIL、MIL等)。 任职要求: 4.0 Required education, experience, knowledge and skills
需要的教育、经验、知识及技能 Ÿ Education: Master degree or above, more than 5 years working software development experience in automotive industry . 学历:硕士及以上学历,5年以上汽车行业软件开发工作经验。 Ÿ Major: Electrical Engineering, Electronic Science and Technology, computer, software, communication and related majors. 专业:电气工程、电子科学与技术、计算机、软件、通信及相关专业。 Ÿ Know well about C programming language, familiar with Bootloader development used in embedded code development. 熟悉C编程语言,熟悉嵌入式代码开发中使用的Bootloader开发。 Ÿ Skilled use of mainstream automotive MCU, like TI, NXP, ST, etc. 熟练使用TI、NXP、ST等主流汽车MCU。 Ÿ Know well about vehicle network communication and related standards like LIN/CAN/CANFD/J1939. Better if know FlexRay/ETHERNET&LIN2.2/100BASE-T1/ISO 11898 , etc. 熟悉车辆网络通信和LIN/CAN/CANFD/J1939等相关标准。了解FlexRay/ETHERNET和LIN2.2/100BASE-T/ISO 11898等。 Ÿ Know well about the basic bottom signal requirements used in motor and solenoid valve control. 熟悉电机和电磁阀控制中使用的基本底层信号要求。 Ÿ Experience in diagnosis development based on UDS, know well about ISO15765 ISO14229 and DoIP. 基于UDS的诊断开发经验,熟悉ISO15765、ISO14229和DoIP。 Ÿ Experience in function safety development, familiar with ISO26262 and ASPICE. 有功能安全开发经验,熟悉ISO26262和ASPICE。 Ÿ Experience in OTA development and related standards. 有OTA开发和相关标准的经验。 Ÿ Experience in signal filtering algorithm. 有信号滤波算法经验。 Ÿ Experience in calibration development based on XCP/CCP. 基于XCP/CCP的校准开发经验。 Ÿ Familiar with Autosar standard, proficient in a tool chain like Vector or ETAS is preferred. 熟悉Autosar标准,精通Vector或ETAS等工具链者优先。 Ÿ Personality: responsible, enterprising, strong sense of teamwork, self-driven, and problem-solving mindset 性格:负责、进取、团队合作意识强、自我驱动、解决问题的心态 Ÿ Excellent communication skills in English and Mandarin both written and verbal. 优秀的英语和普通话书面和口头沟通技巧。